With decades of experience supplying engineered LVL and timber treatment solutions to the Australian construction industry, Dindas Australia now offers a complete H3 pre-primed LVL range designed for reliable above-ground exterior performance.
DindasFrame LVL 10 is a Structural Laminated Veneer Lumber
(LVL) used for framing construction and structural applications
such as lintels, rafters, and suboor components.
Dindas LVL 13.2 is a versatile product with a wide range of applications in construction, including structural beams, lintels, rafters, and floor joists in residential and commercial buildings.
Dindas LVL 14 F17 high-strength laminated veneer lumber product optimised for high-performance and structural applications that require stiffness, durability, and reliability, including framing.
Available up to 12m lengths
LVL 10 and LVL 13.2 (All Dindas Branches) and LVL 14 F17 (VIC Only)
Available as Pre-Primed H3.
AS/NZS 4357.2 and AS/NZS 1604 Series of Standards
Your materials stay protected until the final coat is applied, even in tough site conditions.
For sizes, span tables, and technical information, refer to the individual Dindas LVL 10, LVL 13.2, and Dindas LVL 14 F17 product flyers, or contact your local Dindas Australia representative.
✅ If it’s above ground and can drain and dry, it fits.
❌ If it’s in the ground, embedded, immersed, or permanently wet, it doesn’t.
Note: Always specify and install in accordance with NCC requirements, relevant Australian Standards, and project documentation.
| Feature | H3 Primed LVL | H3 Pine | Unprimed LVL |
|---|---|---|---|
| Structural consistency | ✔ Engineered, uniform | ✖ Variable | ✔ Engineered |
| Straightness & stability | ✔ Excellent | ✖ Prone to twist | ✔ Excellent |
| H3 protection | ✔ Built in | ✔ Built in | ✖ Not standard |
| Factory primer | ✔ Yes | ✖ No | ✖ No |
| Site prep required | ✔ None | ✖ Sand & prime | ✖ Prime required |
| Labour savings | ✔ High | ✖ Low | ✖ Medium |
| Finish quality | ✔ Clean & uniform | ✖ Variable | ✖ Raw |
| External suitability | ✔ Purpose-designed | ✔ Limited | ✖ Limited |
The Dindas H3 Pre-Primed LVL Range is available in two core LVL grades:
LVL 14 F17 (VIC Only)
For sizes, Span Tables, and detailed technical information, refer to the Resources section below, the individual product pages or contact your local Dindas Australia representative.
Dindas H3 Pre-Primed LVL is a structural engineered timber product that combines H3 preservative treatment with a factory-applied primer. It is designed for selected above-ground exterior LVL applications where durability, dimensional stability and presentation are important.
Yes. Dindas H3 Pre-Primed LVL is factory H3 treated and pre-primed, helping reduce on-site preparation and keep construction moving. Builders should still follow current Dindas guidance for handling, installation, resealing and final coating requirements.
Yes. Dindas H3 Pre-Primed LVL is designed for external, above-ground applications where the product can drain and dry. The H3 treatment helps protect against termites and decay, while the primer supports moisture and UV protection during construction.
Dindas H3 Pre-Primed LVL should not be used in ground contact, concrete-embedded members, continuous freshwater wetting or immersion, marine exposure, tidal or splash zones, or areas that trap water and cannot dry out.
Yes. Cut ends, drilled holes and penetrations should be resealed with a compatible primer or sealer and protected before exposure to moisture. This supports durability and aligns with good moisture-management practice.
The Dindas H3 LVL range includes H3 pre-primed options for LVL 10, LVL 13.2 and LVL 14 F17, with LVL 14 F17 noted as limited to Victoria. Check current availability before specifying.
H3 LVL span information should be checked through the relevant Dindas LVL span tables and individual product resources for DindasFrame LVL 10, Dindas LVL 13.2 and Dindas LVL 14 F17. Final member choice depends on grade, treatment, span, loading, exposure and project design requirements.
For outdoor or exposed applications, use fasteners suitable for the exposure condition, treatment and project design. The H3 FAQ PDF references hot-dip galvanised fasteners or stainless steel fasteners, with stainless steel recommended for high-exposure zones.
Do you have questions about your project or want to speak with an Engineered Wood Products specialist? Contact us now for expert advice and guidance.
